Used to break loose the drain fittings and the disposal discharge tube. A proper pipe wrench gets the joint apart without crushing the nut or stripping the threads.
Garbage Disposal Installation southlake TX done right the first time
When your old disposal grinds its last lemon peel, we handle garbage disposal installation southlake TX homeowners can count on. Most jobs finish in under two hours, and we haul the old unit away.
Serving southlake and nearby areas.
How big is the job?
Swap plus parts
New flange, new trap arm, or a dishwasher line that needs rerouting.
- 1. Simple swap Same sink, same drain, same circuit. Pull the old unit and set the new one.
- 2. Swap plus parts New flange, new trap arm, or a dishwasher line that needs rerouting.
- 3. Relocation or rework New sink location, new drain, or a circuit that needs to be run.
Drag the needle to compareTouch and drag the needle
- 30Services from one local team
- 20Areas served around southlake
- Drain firstWe check the trap before the install
- Water testEvery joint checked under full pressure
What our garbage disposal installation includes
Every install covers the full job, not just the swap.
Work order
Garbage Disposal Installation- Old unit removal: We disconnect the old disposal, drain the trap, and pull the unit out. The old disposal leaves with us, so you do not have to figure out how to dispose of it. If the mounting ring is reusable, we clean it and set it aside.
- Flange and seal inspection: The sink flange is the most common leak point on a disposal. We check it for corrosion and pitting. If it is sound, we reseal it with fresh plumber's putty. If it is failing, we replace it and quote the part before we start.
- New unit install: We set the new Insinkerator or Waste King disposal on the mounting ring, attach the discharge tube, and reconnect the dishwasher line if you have one. Horsepower is matched to your cooking habits and sink size.
- Electrical hookup: The unit is wired to the existing switch and grounded per code. We test the circuit before we close up. If the wiring is old or undersized, we tell you what needs to change and what it costs.
- Full water test: We fill the sink and run the disposal with water to check for leaks at every joint. The cabinet floor gets wiped down. If anything drips, we fix it before we leave. You should not have to call us back for the same problem.
What the first visit covers
First visit
We pull the old unit, inspect the flange and trap arm, and confirm the circuit. Then we quote the full install before we start.
Garbage disposal installation at homes
Kitchen sink disposals for Southlake homes, from simple swaps to full upgrades.
Builder-grade swap
Replace a worn 1/3 HP unit with a new one.
Horsepower upgrade
Move up to 3/4 HP or 1 HP for heavy cooking.
Flange and trap repair
Fix leaks at the sink flange or trap arm.
Remodel relocation
Move the disposal to a new sink location.
Garbage disposal installation at businesses
Disposals for commercial kitchens, break rooms, and rental properties across Southlake.
Restaurant kitchens
Heavy-duty units for high-volume food prep.
Office break rooms
Standard units for light daily use.
Rental properties
Durable units that hold up to tenant use.
What garbage disposal installation southlake TX involves
A disposal that is sized right and sealed right lasts a decade. One that is undersized or installed on a dirty drain will jam, leak, and send you back to the phone. We do the drain check and the water test on every job.
Garbage disposal installation southlake TX is the removal of a failed or undersized unit and the mounting of a new one on your sink flange, wired to a switch and sealed against leaks. The job covers more than dropping in a motor: we scrape the old plumber's putty, inspect the sink flange for corrosion, check the P-trap and drain arm for buildup, and confirm the dishwasher discharge line is routed correctly. A 3/4 HP unit handles most Southlake kitchens, while 1 HP makes sense for heavy cooking.
Southlake homes built in the 1990s and 2000s often have original 1/3 HP disposals that jam on fibrous scraps and trip the wall switch. When you search garbage disposal installation near me southlake TX, you want a plumber who carries the right brand and flange kit on the truck, not one who has to make a parts run. We stock Insinkerator and Waste King units in common sizes so the job finishes in one visit.
- What it is
- Removing an old disposal and mounting a new one on the sink flange.
- When it helps
- When the unit jams, leaks, or is too small for your cooking.
- What you get
- A sealed, tested disposal with the old unit hauled away.
Our garbage disposal installation process
Every install follows the same five steps. No guesswork, no surprise add-ons, and no leaving the sink in pieces while we run for parts.
Tools and methods we use on every install
Each method answers a different question. Together they leave very little to guess.
For clearing jams inside the disposal and for opening a slow kitchen drain. We run the auger through the trap arm to pull out food debris before the new unit goes in.
The two brands we stock most often. Insinkerator covers the 1/2 HP to 1 HP range with stainless grind chambers.
Putty seals the sink flange to the sink bowl. Teflon tape wraps the threaded drain connections. Both are single-use items we replace on every install.
When a sink drains slowly even after a new disposal, we run the camera down the drain line. It shows root intrusion, scale, or a collapsed section that a snake cannot fix.
When Southlake homeowners call us
The disposal died the night before a holiday dinner and the sink is full of prep scraps.
We run same-day emergency installs across Southlake.
HomesYou are remodeling the kitchen and moving the sink to a new island location.
We rough in the new drain, run the electrical, and install the disposal at the new location.
HomesYour builder-grade 1/3 HP disposal keeps jamming and you are tired of resetting it.
We upgrade to a 3/4 HP or 1 HP Insinkerator with a stainless grind chamber and sound insulation.
HomesYou are selling the house and the inspection report flagged a leaking disposal.
We install a new unit and provide a written record of the work. The install is code-correct and passes inspection.
Homes
How garbage disposal installation runs in Southlake
Southlake water runs hard, and that scale shortens the life of disposals, faucets, and water heaters. Most homes here were built between 1990 and 2015, so the original builder-grade 1/3 HP disposals are now well past their service life.
Timarron
Many homes here have original 1/3 HP disposals from the 1990s. Upgrading to 3/4 HP is a common call, and the cabinets are usually deep enough to make the swap easy.
Carillon
Newer construction with PEX supply lines and PVC drains. Disposal installs here are straightforward, but we still check the flange and trap arm on every job.
Southlake Town Square
Mix of condos and single-family homes. Some units have tight under-sink cabinets, so we bring compact disposal models and short discharge tubes.
- Timarron
- Carillon
- Southlake Town Square
- Clariden Ranch
From problem to finished result.
Slide to compare the photo with an illustrative inspection view. It is generated from the photo, not a measurement.
PhotoJam-prone 1/3 HP swap in Timarron
Before: A 1998 builder-grade 1/3 HP disposal that jammed every few weeks. The homeowner was resetting it with a broom handle and had stopped using the disposal for anything but light scraps.
After: We installed a 3/4 HP Insinkerator with a stainless grind chamber and sound insulation. The unit now handles celery, peels, and citrus rinds without jamming. Install took 75 minutes, and the old unit was hauled away.
Leaking flange repair in Carillon
Before: A slow drip under the kitchen sink had been going for weeks. The cabinet floor was soft, and the homeowner noticed a musty smell. The flange was corroded and the putty seal had failed.
After: We replaced the flange, resealed it with fresh plumber's putty, and installed a new 1/2 HP disposal. The cabinet floor was dried and treated. Total job time was two hours, and the leak test passed with no drips.
Kitchen remodel disposal relocation in Southlake Town Square
Before: A condo kitchen remodel moved the sink from the wall to a new island. The old disposal was still connected to the original drain, and the new sink location had no drain or power.
After: We roughed in a new drain line, ran a dedicated circuit, and installed a 3/4 HP disposal at the island. The old drain was capped and the old unit removed. The install passed inspection on the first visit.
Common disposal problems we solve in Southlake
Most disposal calls fall into one of a few patterns.
Disposal hums but will not spin
The motor is running but the flywheel is jammed. We cut power, pull the unit, and clear the jam with an auger or by hand.
Leaking at the sink flange
A slow drip under the sink rots the cabinet floor and invites mold.
Disposal trips the reset button
A unit that trips repeatedly is overheating. That usually means the motor is failing or the unit is undersized for what you are putting down it.
Undersized unit jams on scraps
A 1/3 HP builder-grade disposal cannot handle fibrous foods. You end up fishing scraps out of the sink and calling a plumber every few months.
Why Southlake homeowners upgrade their disposal
A new disposal is one of the cheapest kitchen upgrades you can make.
Stops sink backups
A worn disposal leaves food particles in the P-trap, and that sludge hardens into a clog.
Quieter kitchen
Older units rattle and hum because the bearings and shredder ring wear down.
Handles more scraps
Jumping from 1/3 HP to 3/4 HP lets you grind fibrous foods like celery, potato peels, and citrus rinds without jamming.
Protects your pipes
A disposal that no longer grinds fine enough sends chunks into the drain line. Over time, that builds into a sewer line backup.
What you receive on the job
Clear records you can keep and share.
Install record
A written note of the unit model and serial number.
Drain findings
What we saw in the trap arm and drain line.
Parts list
Any flanges, rings, or fittings we replaced.
16 years installing disposals in Southlake
Southlake Oakline Plumbing has been installing and repairing garbage disposals since 2010.
Flange condition
We check for corrosion and pitting where the flange meets the sink bowl.
Trap arm flow
We run water and watch how fast the trap arm drains before installing.
Circuit draw
We check the amperage on the disposal circuit to confirm it is sized right.
Is your Southlake neighborhood covered?
Type your ZIP code or town to check. If you are nearby and not listed, call and ask.
southlake ZIP codes
- 76092
Towns we serve.
Based in southlake and covering the places around it. Pick one for local details.
What Southlake homeowners say
Our old disposal finally died on a Sunday night with a sink full of dishes. I called Monday morning and they had a new 3/4 HP Insinkerator in by lunch. The tech checked the P-trap, replaced the flange, and cleaned up the cabinet before he left. Price was exactly what he quoted on the phone. No surprises.
I had two other plumbers tell me I needed a full drain replacement. Southlake Oakline came out, ran a camera, and showed me the line was fine. The problem was a worn disposal sending chunks into the trap. They installed a new unit and cleaned the drain for less than the other quotes. Honest work.
We were remodeling the kitchen and needed the disposal moved to a new sink location. They handled the drain rework, the electrical, and the install in one visit. Everything passed inspection. I have already recommended them to two neighbors in the neighborhood.
Frequently Asked Questions
Short answers for the first few minutes. The team can cover the rest.
Still have a question?
Describe what you are seeing and we will point you to the right next step.
(682) 470-5111A basic 1/2 HP swap sits at the low end; a 1 HP Insinkerator with a new flange and P-trap work sits at the high end. If your sink needs drain cleaning or the electrical connection needs repair, that adds to the total. We quote the full price before we start.
You can, but most homeowners regret it. The job involves wiring a 120V circuit under a wet sink, sealing the flange against leaks, and getting the P-trap alignment right. A bad seal drips into the cabinet for weeks before you notice. A miswired unit can trip the breaker or worse.
A standard swap takes 60 to 90 minutes. If we have to replace the sink flange, redo the P-trap, or run a new electrical connection, plan on two to three hours. We block a two-hour window for every install so there is no rush and no cutting corners on the seal or the wiring.
We handle both on every install. That keeps the job code-correct and keeps your homeowner's insurance intact if anything ever goes wrong.
Related Services
Other services from the same team.
- Water Softener InstallationHard water leaves scale in pipes and shortens water heater life.
- Water Softener RepairWhen a softener stops softening, the issue is often a failed resin tank, a clogged brine line, or…
- Water Filtration System InstallationWhole-home and under-sink filtration systems improve taste and remove contaminants.
Need garbage disposal installation southlake TX today?
(682) 470-5111We carry Insinkerator and Waste King units on every truck and can usually install the same day you call. Upfront pricing, old unit hauled away, and a clean cabinet when we leave.
contact Southlake Oakline Plumbing
Call us at (682) 470-5111 for same-day service or to schedule an appointment. You can also email [email protected] or stop by our office in Southlake.